Several ways to use the safety chuck. The safety chuck intersecting line cutting machine has a simple structure. When calculating the system, one rotation of the chuck is used as a parameter. It has a correct degree measurement. Relatively speaking, the roundness requirements of the pipe are also lower. Sometimes the pipe is slightly curved, and it can be cut by adjusting the position of the bracket. During operation, it is very important to pay attention to the adjustment of the bracket position at all times to maintain the level of the pipe. If this position is not adjusted well, large cutting errors will occur. In addition, there is always a blind area close to the chuck area that cannot be cut, which affects the yield rate of the pipe. Safety chucks are generally used for small-diameter pipes with a diameter not exceeding 600mm, and this type of structure is often used. The outer chuck can be provided with corresponding transmission slots and release slots. The outer chuck can be provided with a boss, and the inner chuck can be provided with a groove that matches the boss. The positioning mechanism can be a positioning spring set on the outer chuck. The hydraulic chuck is set at the drill pipe connecting end of the spindle to slow down the Read More »

　　What are the types of indexing chucks? The indexing chuck uses a belly tower wrench to rotate a bevel gear, which drives a flat rectangular thread, and the three jaws move in a central motion. The pitch of the flat rectangular thread is the same, so the three claws move at the same distance and function as an automatic center. The three-claw disc consists of a large bevel gear, three small bevel gears and three claws. Three small bevel gears mesh with a large bevel gear. The back of the large bevel gear has a plane thread structure, and three claws are evenly installed on the plane thread. When the indexing chuck pulls the small gear with a wrench, the large bevel gear will rotate, and the flat threads on the back will cause the three claws to approach or withdraw from the center at the same time. Because the four acromions are used to move the four feet respectively, the common four-foot clamps do not play a self-centering role. However, the position of the four legs can be adjusted to clamp various rectangular and irregular workpieces. When turning a large number of workpieces with an indexing chuck, a soft jaw plate can be used during processing to improve the process. Read More »

　1) Reduce labor intensity and enhance corporate image. The use of pneumatic chucks can not only greatly reduce the workload of workers while improving production efficiency, but also make your company a model of caring for workers. It can also add new highlights to corporate personnel recruitment and improve product market competitiveness. It can also improve the quality of equipment and enhance the overall image of the company. It is the first choice for equipment improvement for large-volume mechanical processing companies. 2) The structure is simple and easy to install. The pneumatic chuck is configured as a chuck, a pneumatic gyrator and an electronic control part. There is no need for tie rods during installation, which changes the traditional pneumatic and hydraulic chucks' complex structures and troublesome installation (generally, it takes 2 working days for professionals to install). By reading the installation instructions and schematic diagrams, users can complete the entire installation process in about 1 hour. This can not only save users high installation fees and production costs, but also improve the operating efficiency of machine tools for users. 3) No investment in consumables required Read More »

　A chuck is a mechanical device used to clamp workpieces on machine tools. According to the number of chuck claws, it can be divided into: two-claw chuck, four-claw chuck, six-claw chuck and special chuck. Today we will take a three-jaw chuck as an example to introduce the heat treatment of the jaws using high-frequency induction quenching equipment. The three-claw chuck uses a large wrench to rotate the bevel gear. The bevel gear drives the plane to thread, and then drives the three claws to move centripetally. Since the pitch of the plane rectangular thread is equal, the three claws move at the same distance and have an automatic centering effect. The three-claw chuck is composed of a large bevel gear and three claws. The three claws are equally installed on the flat thread, and the small bevel gear rotates when a wrench is used. The flat thread on the back allows the three claws to move toward or withdraw from the center. The material of the claw is 45 steel, the overall dimensions are 70.3*56*20.5mm, and the tooth width is 12mm. Hardness ≥52HRC, 30-40HRC on both sides and base, 53-58H on the rest Read More »

　　Background technology: The pneumatic chuck has a body accuracy of 0.010mm and a high speed of up to 5000rpm. It is a high-end and high-performance pneumatic chuck with hollow through holes that can work with an automatic feeding system to improve production efficiency. Currently, pneumatic chucks have been widely used in various applications such as workpiece clamping systems for CNC lathes or special processing machines, automation of traditional lathe modifications, grinding machines, or fourth-axis indexing chucks installed in CNC machining centers. However, the traditional pneumatic chuck must rely on manpower when locking the workpiece. Manually tightening the workpiece with a chuck wrench is time-consuming and laborious, which seriously affects production efficiency. During the rotation of the pneumatic chuck, it is easy to cause its own displacement due to the rotation speed, resulting in a short service life of the equipment. Therefore, those skilled in the art provide a rotatable hollow three-jaw pneumatic chuck to solve the problems raised in the above background art. Technical implementation elements: The purpose is to provide a Read More »

The characteristics of movement on machine tools are classified into the following categories: (1) Lathe type fixtures: including fixtures for lathes, internal and external cylindrical grinders, and thread grinders. The characteristic is that the fixture rotates together with the workpiece. (2) Milling machine fixtures: including fixtures for milling machines, planers, surface grinders and other machine tools. The characteristic is that the fixture is fixed on the workbench and only performs longitudinal or transverse reciprocating or rotary motion. (3) Drilling and boring machine fixtures: used for drilling, enlarging, reaming and other processes on the drilling machine or in the boring process. In fact, the fixture is fixed on the machine tool, and the tool is fed through the guide device on the fixture. Read More »

Special fixtures are specially designed and manufactured to meet the requirements of a certain process of processing a certain workpiece. Its functions mainly include the following aspects: 1. Ensure the position accuracy of the processed surface of the workpiece, such as the distance accuracy, parallelism, coaxiality, etc. with other surfaces. For laymen, it is often difficult to achieve precision requirements when using general-purpose fixtures to process workpieces that are more complex and require higher positional accuracy. 2. The process time is shortened, thereby improving labor productivity. The time required to perform a certain process mainly includes the maneuvering time required to process the workpiece and the auxiliary time required to load and unload the workpiece. After using special fixtures, the work of installing workpieces and changing workstations can be greatly simplified. Line drawing and alignment are no longer required, which shortens the auxiliary time of the process and saves the line drawing process, thus improving labor productivity. In production, due to the use of multiple workpieces Read More »

An indexing chuck is a mechanical device in a machine tool used to clamp workpieces. A mechanical attachment that secures and positions the workpiece using uniform radial movement of the movable jaw on the card body. The chuck usually consists of three parts: the card body, the movable jaw and the jaw driving mechanism. The diameter of the card body is at least 65 mm and more is 1500 mm, and there is a hole in the center through which the workpiece or bat can pass. There is a cylindrical or short tapered structure on the back, which is connected to the end of the machine tool spindle directly or through a flange. Clamps are commonly installed on lathes, cylindrical grinders and internal cylindrical grinders and can be used with a variety of indexing devices that can be used for milling and drilling. A 'chuck' is a mechanism used to clamp workpieces on a machine tool. What are the classifications of indexing chucks? In terms of the number of claws, it can be divided into two claws, three claws, four claws, six claws, special claws, etc. The power used can be divided into manual chuck, pneumatic chuck, hydraulic chuck, electric chuck, mechanical chuck, etc. Structurally it can be divided into blanks Read More »

Characteristics of fixtures When processing workpieces on machine tools, we can see two different situations: one is to use a measuring tool such as a needle or indicator to align according to a certain surface of the workpiece, or according to the line drawn on the surface of the workpiece, so that the workpiece is in the correct position required on the machine tool, and then clamp the workpiece for processing; the other is to install the workpiece on a fixture for processing. In order to process a surface that meets the specified technical requirements on a certain part of the workpiece, various devices are generally used to accurately, conveniently and reliably install the workpiece on the machine tool according to the structural shape of the workpiece, the processing method and the production batch, and then process it. The device used to install the workpiece to determine the relative position of the workpiece and the cutting tool and clamp the workpiece is called a 'machine tool fixture'. In actual production, such as piston and connecting rod production lines, fixtures are used in almost every process. It is very obvious that if the clamp is not used, not only Read More »

The market competitiveness and development prospects of power chucks As early as the 1970s, a company in Germany had developed the most advanced power chuck in the world at that time. According to data, the chuck at that time could reach 10,000 revolutions per minute, and in normal operation it could achieve 8,000 revolutions per minute. At present, power chucks have been widely used not only abroad but also domestically, and are used in mechanical processing and high-precision CNC machine tools. With the rapid development of modern computer technology, high-tech applications are becoming more and more common in modern design. Computer-aided design methods such as CAD, CAM, and CAE are becoming more and more common internationally. These modern design methods not only increase the design speed, but also make the designed products more reliable and beautiful, save a lot of manpower and material resources, and greatly improve the competitiveness of the products. Read More »

　1. Larger static clamping force 1. The clamping force will vary depending on the type of oil used, the height of the upper claw and other conditions. The standard values ​​we list in the specification sheets are based on the following conditions. 2. Use standard soft claws imported from Taiwan, China, and when measuring the clamping force, use a clamping force tester placed in the middle of the height of the soft claws. 3. Use chuck lubricant or molybdenum disulfide lubricant. 4. When installing the upper claw, the tightening torque of the screw must be tightened according to the standard torque. 5. The allowable pulling force is the maximum allowable pulling force of the pull plate. 6. When using a hydraulic station, the oil pressure outflow must be at least 20L/min, and the oil pressure must be controlled separately by the controller or pressure reducing valve of the hydraulic station. 2. The standard for determining the higher rotation number of a chuck with a higher rotation number is: when the dynamic clamping force (clamping force during rotation) drops to 1/3 times the actual measured value of the static clamping force Read More »

　　01. Selection of soft claw material: The 'soft' here means: good processing performance, but it does not mean that it must be lower than the hardness of the workpiece. For mass production, the hardness of the soft claw will have a great impact on the stability of processing. Choosing a soft claw material with a higher hardness than the workpiece will not only increase the service life of the soft claw, but also have a positive impact on the stability of processing. 02. The installation position of the soft claw on the chuck: Any T-shaped block exceeding the maximum diameter of the chuck is not allowed, which will cause great safety risks. 03. Pressure and position when using the claw trimmer: It is recommended that the pressure during use is close to the pressure during workpiece processing. The chuck is in the middle of the range of movement during processing, and the direction of the clamping force during claw trimming is consistent with the direction of the workpiece clamping force. Read More »